This page last changed on Nov 20, 2014 by mqandeel.

Dears, Thanks for this great Project.

I'm trying to get OpenRemote Controller working on an Ubuntu 14.04 machine to control and KNX bus through K-BUS IP GW with address 192.168.1.239. I sat the configuration in the config.properties for the host IP and port but it didn't connect. I get the following in the knx-debug.log

INFO 2014-11-20 10:16:59,855 (KNX): KNX IP interface hostname set to '192.168.1.239'
INFO 2014-11-20 10:16:59,855 (KNX): KNX IP interface port set to '3671'
INFO 2014-11-20 10:16:59,855 (KNX): KNX PhysicalBus clazz set to 'org.openremote.controller.protocol.port.DatagramSocketPort'
INFO 2014-11-20 10:16:59,856 (KNX): Scheduled reconnection task
WARN 2014-11-20 10:16:59,856 (KNX): Unknown KNX property '<property name = "name" value = "SPOT_CNTR_SW_STATUS"/>'.
INFO 2014-11-20 10:16:59,858 (KNX): Trying to create connection
INFO 2014-11-20 10:16:59,858 (KNX): Removing connection
INFO 2014-11-20 10:16:59,861 (KNX): KNX Connection manager resolving local host IP addresses...
INFO 2014-11-20 10:16:59,862 (KNX): Found candidate NIC: name:vmnet8 (vmnet8)
INFO 2014-11-20 10:16:59,863 (KNX): Skipped IPv6 address (not supported by KNX) /fe80:0:0:0:250:56ff:fec0:8%5
INFO 2014-11-20 10:16:59,863 (KNX): Added candidate IP address to set - /192.168.101.1
INFO 2014-11-20 10:16:59,863 (KNX): Found candidate NIC: name:vmnet1 (vmnet1)
INFO 2014-11-20 10:16:59,863 (KNX): Skipped IPv6 address (not supported by KNX) /fe80:0:0:0:250:56ff:fec0:1%4
INFO 2014-11-20 10:16:59,863 (KNX): Added candidate IP address to set - /192.168.48.1
INFO 2014-11-20 10:16:59,863 (KNX): Found candidate NIC: name:wlan0 (wlan0)
INFO 2014-11-20 10:16:59,863 (KNX): Skipped IPv6 address (not supported by KNX) /fe80:0:0:0:3e77:e6ff:fe18:620b%3
INFO 2014-11-20 10:16:59,863 (KNX): Added candidate IP address to set - /192.168.1.197
INFO 2014-11-20 10:16:59,863 (KNX): Skipping loopback interface: name:lo (lo)
DEBUG 2014-11-20 10:16:59,875 (KNX): Creating KNX bus with org.openremote.controller.protocol.port.DatagramSocketPort
DEBUG 2014-11-20 10:16:59,881 (KNX): Creating KNX bus with org.openremote.controller.protocol.port.DatagramSocketPort
DEBUG 2014-11-20 10:16:59,882 (KNX): Creating KNX bus with org.openremote.controller.protocol.port.DatagramSocketPort
INFO 2014-11-20 10:16:59,884 (KNX): Created KNX Command FRAME L_Data.req 0.0.0 -> 0/0/6 Data: 0x00 for group address '0/0/6'
DEBUG 2014-11-20 10:16:59,891 (KNX): Polling device status for FRAME L_Data.req 0.0.0 -> 0/0/6 Data: 0x00
INFO 2014-11-20 10:16:59,891 (KNX): KNX connection not available.

Any help please to get it connecting to the KNX IP?

  • BNIP-00/00.1
    The KNX IP Interface connects the EIB/KNX system with the Ethernet network via an Ethernet RJ45 interface in the front,It serves as an interface between KNX installations and IP networks and can configure, parameterize and commission the EIB/KNX installation as well as bus monitor via the LAN using the ETS (ETS3 or later) software

i.e. BNIP-00/00.1 can be used for ETS programming ONLY
for Open remote or other vis. systems use Weinzierl 730 or some similar

Posted by alexeyand at Nov 25, 2014 14:20
Document generated by Confluence on Jun 05, 2016 09:37